This is a step by step drawing tutorial on how to draw Gaige from Borderlands. Watch this video of how to draw Claptrap from Borderlands the Pre-Sequel and you'll be able to draw him in no time, follow the step by step tutorial or the pictures provided. How to Draw Claptrap from Borderlands The Pre-Sequel Claptraps appear in both Borderlands, and Borderlands 2.
#Siren tattoo tutorial manual
This robot's original design name is CL4P-TP which are basically general purpose robots that are used for manual labor to work. Get your pencils in hand because we are about to learn "how to draw Claptrap", step by step. This is a step by step drawing tutorial on how to draw Claptrap from Borderlands. Learn how to draw a Claptrap with the following simple step to step tutorial. They may be found in populated areas or guarding access points between different maps, but are more commonly found in need of repair. CL4P-TP General Purpose Robots, more commonly known as Claptraps, serve as the stewards of Pandora. Today we will show you how to draw a Claptrap from the game Borderlands. How to Draw a Claptrap from the game Borderlands with Easy Step by Step Drawing Tutorial This is a step by step drawing tutorial on how to draw Axton from Borderlands. This is a step by step drawing tutorial on how to draw Athena from Borderlands. Watch this drawing tutorial and learn how to draw Athena from Borderlands the Pre-Sequel, you can follow the step by step video lesson or the illustrations provided. How to Draw Athena from Borderlands The Pre-Sequel Borderlands Video Game Illustrations & Cartoons Drawing Lessons and step by step drawing tutorials for drawing them. If your loudspeaker does not have a connector then just plug the loudspeaker wires directly into the board.Home > Directory Home > Drawing Lessons > How to Draw Video Games Characters > How to Draw Borderlands Characters LEARN HOW TO DRAW BORDERLANDS CHARACTERS & VIDEO GAME CARTOONS & ILLUSTRATIONS DRAWING LESSONS Two wire links are used to connect the loudspeaker to the breadboard here. Connect the negative lead of the loudspeaker to the bottom rail of the breadboard. Step 8: Insert Resistor R3 Connect the LoudspeakerĬonnect the positive lead of the loudspeaker to the right lead of R3. Get the loudspeaker and two wire links ready. Step 7: Wire Transistor Q1 to Capacitor C2 Connect R3Ĭonnect one lead of R3 to the collector of Q1 (right lead) and the other to a tie point to the right. Using two wire links, connect the collector of Q1 (right pin) to the unconnected lead of C2. Using two wire links, connect the emitter of Q1 to the top rail of the breadboard. Step 5: Wire Q2 and Insert Q3 Wire Q1's Emitter Make sure that the flat face of Q1 is pointing to the bottom rail. Insert Q1 so that its middle pin (base) connects to the other end of the wire link that was just inserted. Insert a wire link so that it connects the right pin of Q2 (collector) to a tie point to the right. Get the PN2907 PNP transistor (Q1) and a wire link ready.
The other lead of C2 must be positioned to the right of this connection. Plug one lead of C2 into the same vertical connecting strip where R2 and the link that was just inserted join. Step 3: Insert Transistor Q2 and Wire Link Connect C2Ĭonnect the middle lead of transistor Q2 to R2 by inserting a wire link across the middle breadboard channel. Get the 100n (0.01uF) capacitor (C2) and a wire link ready. Connect the left lead (emitter) to the bottom breadboard rail using a wire link. With the flat face of Q2 towards the bottom rail of the breadboard, insert the transistor so that its middle lead (base) lines up with the right lead of R2 above it. Step 2: Insert Capacitor C1 and Wire It Insert Q2 Get the PN2222 NPN transistor (Q2) and a wire link ready. One capacitor lead must be above the middle channel of the breadboard and the other lead below it. Step 1: Insert Resistor R1 and R2 Connect C1Ĭonnect the positive lead of the 1000uF capacitor (C1) to the vertical breadboard strip that connects R1 and R2.Ĭonnect the negative lead to the bottom rail through a wire link. Get the 1000uF capacitor and a wire link ready. Connect R2 to R1 and to a tie point to the right. Insert the 33k resistors: Connect R1 from the top rail to a tie point in the board below. Click the button below to make a donation. You can help the Starting Electronics website by making a donation:Īny donation is much appreciated and used to pay the running costs of this website.
0 kommentar(er)
